The dull would not be able to cut smoothly as a sharp blade, as a result, it will bind in the wood and you know what comes next; kickbacks! When you are using a circular saw, you should not stand right behind the line where the saw is cutting. If any kickback incident occurs, the saw will come right in the backward direction to the user. And if you stand in its direction, it will not bother to run through your body.
Hold the saw with both of your hands tightly when you are cutting. This will give you more chance to control the saw in case it kicks back.
And also remember to keep one of your fingers on the trigger of the circular saw so that you can release immediately if it starts to kickback. Clamp the workpiece of yours properly. If the wood is too loose then you might lose the track of the cut and make the cut on the unwanted areas.
This both not good for your project and also increases the risk of kickbacks. Put the workpiece in a flat surface. If the wood piece is too long then it is a must to put in on a flat surface.
Laying it just on top of two sawhorses is a bad idea. Use more in such cases. The advantage of 2X4s is that you can move them around when you need to make cuts in different places of the workpiece. So they will not get in your way or in the way of the circular saw blade while cutting.
If you are using an electric circular saw then you will also have a power cord with it to handle. This cord supplies the electric power to the saw. Always use clamps or whatever you prefer to use to secure it in place.
Another major cause of kickback is not having a firm hold and control over your circular saw. You need to hold it firmly on both the front and the back. With electric circular saws that have electric brakes, you can stop the saw within. Although circular saws can be incredibly dangerous, if you are not careful, they are also very useful.
When using a circular saw, do you understand what kick back is and how you can prevent it? My manual also covered many additional safety tips and gave advice for making good cuts.
Kickback happens when the saw blade binds or stalls suddenly in the wood and the saw gets driven back toward you. It can also depend on the nature or condition of the wood.
Are you cutting hardwood or softwood or plywood? Does the wood have any knots which could cause problems? If you feel the saw beginning to bind, release the trigger so the blade will stop. I recommend using some type of fence or guide for making long ripping cuts.
I also believe in keeping both hands on the saw to maintain better control. And that holds true for most other saws. When starting a cut, make sure the blade is not resting on the wood before you push the trigger. Keep the saw blade back from the wood, pull the trigger and let the saw blade come to full speed. Then slowly advance the saw into and across the wood. Keep the saw steadily moving and make a continuous cut across the board. You need to think about this especially for longer cuts. Can you comfortably and safely make those cuts and not lose control of your saw?
Think about your body position behind the saw. This is what is also suggested when pushing a board through a tablesaw. Point A, B, or C? But, there will probably be a big rough split on the end because you needed another hand to support the off-cut if you are right handed. If you cut through at point A, holding one piece with your left hand and letting the other drop to the ground, but it'll splinter again.
It is fairly safe, but you have another thing to consider. Look at the sketch below. The two ends on the stools want to stay put, but when you are pushing in the middle, and as soon as the bit of timber remaining to cut becomes small enough, the whole lot wants to bend, and sure enough, bind on the back of the blade.
A better way to do it would be to cut at point C, where, as you are getting almost through the cut, you can support the off-cut with your left hand in such a way that you help the cut to open up. Clamp down the timber if it wants to slide about on the stools.
Make a bench if you are cutting many pieces up. There are several ways to do this: [4] X Research source Use some of the smaller pieces to make a bench. Then with a few lumps of off-cuts under the piece being cut you can cut safely. Make a bench out of a couple of planks. Cut on the ground, using packers and one foot on the timber being cut. Include your email address to get a message when this question is answered. By using this service, some information may be shared with YouTube.
If you are cutting off rafter ends to fix a fascia, you should either have them pre-cut to size before you fix them, or close to it, so that the offcuts are small enough to be no problem. That way you have one hand to hang on with and one to cut with. Helpful 0 Not Helpful 0. After you've dealt with kickback, learn to make straighter cuts with your circular saw to improve your technique further.
0コメント